The easiest way to shorten curtains without hemming is to move the curtain rod. Optimum rod placement is one-third of the distance between the ceiling and the top of the window frame, but mounting the curtains higher will increase the perceived size of the window, and also create the illusion that the walls are taller.
How do you shorten a curtain without cutting it?
When curtains appear too long, try sewing a hem, which can allow you to shorten curtains without cutting curtains to length so you can retain the fabric if you want to. Another way of shortening curtains is to incorporate a folded design with buttons as fasteners. Folding the curtain hem up creates a double hem.
What can I do if my curtains are too long?
Creative Ways to Shorten Long Curtains
- Tieback and Blouse. The position of the tiebacks can give long curtains a little lift. …
- A Little Off the Top. Shorten tab-top or tie-style curtains at least a few inches by turning them into grommet-hung curtains. …
- Shorten as Pleats or Scarves. …
- Raise the Rod. …
- Tier Up.
Can curtains be cut to length?
While the curtains are still hanging, fold the bottom of the curtains under to the desired length. Use the stick pins to hold, to keep it folded and in place. Bring the curtain bottom up to the ironing board and iron a crease on the new fold. Cut off excess curtain a couple of inches past the fold and remove the pins.
Can you cut curtains in half?
My husband helped me hold them taut, and I cut them in half lengthwise. It doesn’t even need to be perfectly straight, because that edge will be folded under. Then, I followed the directions on the hem tape. I cut a strip the length of the curtain panel and pinned it along the cut edge, paper side up.
Is it better to have curtains too long or too short?
Short curtains and drapes are not ideal, and most often you don’t want curtains that hang more than an inch above the ground. Too short curtains can not only look outdated, but they can also sometimes make the ceiling look lower. However, there are a couple of scenarios where short curtains are a more practical option.
Are curtains supposed to drag on the floor?
Interior designers note the bottom of your curtains should fall to the floor, and you can even let them “puddle” a bit. However, if you don’t want your curtains to drag on the floor when you open and close them, let them stop about an inch from the floor, but no more.
Can you use fabric tape to hem curtains?
Iron-on tape is supplied with all curtains/voile curtains to enable you to create a hem at the desired length. … Place the tape at the bottom of the curtain with the glue side against the wrong side of the fabric. Iron, then remove the protective paper. Turn down the fabric at the desired hem length and iron again.
Can you cut curtains with scissors?
Cut Your Curtains
Once you have measured your new hem and pinned it out, cut off the excess curtain using fabric scissors by following the pinned line.
How do you fix too short curtains?
How to Fix Curtains That Are Too Short
- Pull the curtains to the side and use a tieback. …
- Add material to the bottom of the curtains in a color that will complement the curtain and the existing decor.
- Add trim to the bottom of the curtain that matches drapes or tiebacks.
Can you hem curtains?
Curtain hems are folded twice at the bottom, so you will need twice as much fabric for the hem. This means that you will need to cut your curtains longer than you want them to be. The longer the curtain is, the wider the hem needs to be; this will help make it look more proportionate.
What is the hem allowance for curtains?
The ‘Norm’ if you like, would be to have a 3 inch (7.5cm) hem. However if you are making curtains that are quite large or long, you may find that a 4 inch (10cm) hem gives proportionately better appearance. Or, if your curtains are going to be quite short, hemming them with a 2 inch (5cm) hem would be sufficient.
Should I cut my curtains?
Nearly any curtain design still looks good if you shorten it from the bottom instead of the top. Avoid cutting by folding up the bottom to the desired curtain length and pressing it with a hot iron to create a crisp edge.