# You asked: How do you calculate yardage for the back of a quilt?

Contents

## How do you figure out yardage for quilt backing?

Take your backing length measurement and multiply it by the number of WOFs you need. 74″ x 2 = 148″ This is how many inches of fabric you need. Now, divide that number by 36″ to get how much yardage you need. Round up to the nearest ¼ yard and you get 4 ¼ yards.

## How much bigger should the back of a quilt be?

Quilt Back:

Size of the back: must be at least 6″ wider on each side, top and bottom, than your quilt top. A total of 12″ larger than your quilt top. Trim the top and bottom edges of your backing so they are straight and square.

## How much fabric do I need for the back of a queen size quilt?

A standard queen size quilt that is 88 inches wide and 96 inches long takes about 8 yards of fabric for the front of the quilt and another 8 yards of fabric for the back of the quilt, depending on the pattern and fabric you choose.

## How do you figure out yardage for fabric?

Total number of pieces divided by number of pieces that fit into width equals number of rows you need. Number of needed rows multiplied by length of one piece equals total project in inches. Total project inches divided by 36 inches equals total yardage needed (rounded up to the whole number).

## How many yards do I need for backing?

The amount of yardage needed is rounded up to the nearest eighth of a yard. For example, suppose the backing you need for a quilt is 52 inches wide by 96 inches long and the fabric you wish to use for the backing is on a bolt of fabric whose width is 43 inches. The yardage required is 5 1/3 yards.

## Should the batting be the same size as the backing?

The batting also needs to be larger than the top but not larger than the backing. I can always trim the batting if it is too large but harder to make it bigger if too small, although I have pieced batting together as needed with satisfactory results it is always best to do that before sending it to the longarm quilter.

## Is batting bigger than quilt top?

As for your batting and backing, they should be both cut 6-8 inches larger than the quilt top. … At the same time, if you’re adding a lot of stitches to the quilt top, the quilt will shrink up a bit, too.

## Can I use a bed sheet for quilt backing?

We’ll talk about this in more details, but here’s the short story: you can ABSOLUTELY use bed sheets for quilt backs! There’s a few obvious benefits to this: No piecing together a quilt back! This is the best benefit – just buy a sheet big enough to back your quilt and you don’t need to piece it together!

IT IS INTERESTING:  When did indigenous start beading?

## How much fabric do I need for the back of a quilt?

The quilt backing needs to be larger than the quilt top to allow extra for fabric that is taken up during quilting and for stabilization when using a quilting frame. Always add 8″ to both the length and width measurements so you have an extra 4″ of fabric all around. Trim off the selvage of all backing fabrics.

## How many yards of fabric do I need for a queen-size comforter?

Based on a standard queen comforter size of 90 inches wide by 95 inches long, you need a bare minimum of 11 yards, but 12 yards adds extra for straightening the fabric. Purchase an additional one to two yards if the fabric has a pattern or stripes you must match.

## How many yards of fabric do I need for a 108 queen-size quilt?

If you purchase two yards of 108″ wide backing at \$17.99, your total is \$35.98. That is a savings of over 50% or \$35. Bonus, you will have enough fabric for your binding. The average queen-size quilt (84″ by 92″) will require 7.5 yards of backing and .

## How much backing fabric do I need for a king size quilt?

108″ backing is great for king or queen sized quilt, but a touch overkill for baby blankets. Now everyone get their supplies: pencil, paper, calculator, your quilt top and something to measure it with (cutting mat or measuring tape), that half empty bottle of Advil or the rest of the wine.