As illustrated in Fig, 4.7a, in weft knits, a loop, called a needle loop, consists of a head and two legs, and the section of yarn connecting two adjacent needle loops is called the sinker. In warp knits, the needle loop is divided into overlap and underlap, as illustrated in Fig. 4.7b.
What are knitted loops called?
In weaving, threads are always straight, running parallel either lengthwise (warp threads) or crosswise (weft threads). By contrast, the yarn in knitted fabrics follows a meandering path (a course), forming symmetric loops (also called bights) symmetrically above and below the mean path of the yarn.
What are the knit trims?
Knit trims are designed and used primarily on knit sportswear but may also be used to trim woven sportswear. Knit trims may be cut and sewn or knitted to specified dimensions, depending on methods of fabrication. Circular knit trims are produced in tubes that range from 1” to 60” in circumference.
What is looper knit?
In loop knitting, long, dangling loops are introduced into the middle of a knitted fabric or along an edge (fringe border). … An overall array of such loops may be used to give a “shaggy” look to the fabric and/or make it warmer, e.g., tufting the inside of mittens.
What is knitting terminology?
ktbl = knit through the back loop; results in twisted knit stitches; also known as k1b. k1b= knit through the back loop, can also be abbreviated as ktbl. KYOK = knit, yarn over, knit into the same stitch again is an increase technique used when knitting stacked increases. … M1L = Make one left; a left-leaning increase.
What is sinker loop knitting?
Sinker loop: The lower part of the knitted loop is technically referred as sinker loop. It is the connection of tow legs belonging to the neighboring stitches lying laterally. The yarn portion that connects two adjacent needle lops belonging in the same knitted course. Bottom arc also called sinker loop.
What is knit 1 Purl 1 called?
23 Comments. If you know how to knit and purl, then you can make a textured pattern called single rib, or “knit one purl one”. k1p1 single rib. Single rib is a stretchy piece of knitting often used for cuffs and hems.
What are the different types of trims?
Broadly, trims can be categorized into four types, i.e. bindings, edging, flat applications and other trims. Bindings are functional trims used to finish the edges of the garment, like finishing of necklines, hems, armholes, openings, etc.
What is loop length in knitting?
Loop length is found by dividing the stretched yarn length by the number of loops in one course and expressed as follows: Loop length ( ) = uncrimped yarn length in one course/number of loops in one course ( ) [3.
What is loop yarn?
Loop yarn is a thick, puffy yarn that has loops pre-sewn into it. To knit with loop yarn, you use your fingers, rather than needles, to stitch the loops together. It’s a great introduction to knitting for beginners, hobbyists, or even kids. Plus, because of its fleecy texture, loop yarn doesn’t slip easily.
What is held loop?
A held loop is an old loop that the needle has retained. It is not released and knocked-over until the next, or a later, yarn feed. A held loop can only be retained by a needle for a limited number of knitting cycles before it is cast-off.
What is open loop in knitting?
The lower part of the knitted loop is technically referred as sinker loop. It is the connection of two legs belonging to neighboring stitches lying laterally. Open loop: The open loop is one in which the loop forming yarns do not cross at the bottom of the loop.
What is needle loop?
The needle loop is the basic nuit of knitted structure. When tension in the fabric is balanced and there is sufficient take-away tension during knitting, it is an upright noose formed in the needle hook. It consists of a head(H) and two side limbs or legs(L).
What is a foll row in knitting?
foll means “following”. beg means “beginning”. cont means “continue”.